GENUINE ETA 2824 movement yellow, runs. (hour wheel discolored from storage) 25.9mm diameter. (I don’t think it’s the same as 2824-2). I think it’s new, but from aged from being in storage. It may be pre-owned, so I’m marking it as pre-owned just to be sure. Be prepared to oil/clean and/or repair to make it…
Vintage Arnex 20 ATM Diver Watch withAll SS Case, ETA 2472, Runs FOR PARTS/REPAIR
FOR REPAIR – while the date and time can be set without issue and the crown wound, the movement will sometimes run for several hours at a time while at other times it stops intermittently. When it does run consistently it loses several minutes. Additionally, a movement screw has come loose and will be included…
Vintage Arnex Divers Chronograph withChocolate Brown Dial, Runs FOR PARTS/REPAIR
- by: Admin
- In: vintage
- On
- Comments: 0
- Tags: arnex , brown , chronograph , dial , divers , partsrepair , runs , vintage , withchocolate
While the movement runs strong and keeps accurate time over an approximate 41 hour power reserve period, none of the chronograph functions work (pushers don’t engage so the start/stop/reset function does not work – sweep seconds hand and minute counter hand don’t move). Given this and considering that the movement has likely never been serviced,…
Vintage Paul Le Grande Diver Watch withAged Dial, All SS Case, Runs FOR PARTS/REPAIR
While the date and time can be set without issue and the crown winds beautifully, the movement runs sporadically. I’ve observed it running strong and keeping accurate time for more than a 24 hour period on multiple occasions but I’ve also observed it stop inconsistently at other times. A complete overhaul is needed. This vintage…
Vintage Tressa World Time Diver Watch withBlue Dial, Patina, Runs FOR PARTS/REPAIR
Until recently the movement was keeping accurate time. While the seconds hand continues to run strong, albeit fast, the minute hand now has a tendency to start and stop, moving inconsistently on its own. Sometimes the watch runs as it should, although a bit fast, during a full power reserve cycle while other times the…
Vintage Sandoz 20 ATM Diver Watch withPatina, Signed Crown, Runs FOR PARTS/REPAIR
While the movement runs strong, keeps accurate time and the date wheel rolls over automatically as it should, when the screwdown crown is pulled out to set the time it tends to skip and every several revolutions sounds like crunching lettuce. Also, when setting the time the hour hand sometimes gets stuck and bounces uncontrollably…
Old Vintage Tudor Rolex Royal Watch Movement For Repair It Kinda Runs! Parts
Antiques and Jewelry By The Sea. Old Vintage Tudor Rolex Royal Watch Movement For Repair – It Kinda Runs! Title: Old Vintage Tudor Rolex Royal Watch Movement For Repair – It Kinda Runs! Description: This 1960’s Tudor Royal watch movement came out of an estate – it has spent many years just sat in a…
Vintage Sheffield Day-Date Diver Watch withMint Dial, Runs Strong FOR PARTS/REPAIR
While the movement runs strong it tends to run anywhere from 45 minutes to more than an hour slow at the end of its approximate 38 hour power reserve period. And while the date wheel rolls over the day wheel does not. Additionally, occasionally after winding the crown several full revolutions there will be a…
Vintage Ollech & Wajs Selectron Chronograph withDivers Case, Runs FOR PARTS/REPAIR
- by: Admin
- In: vintage
- On
- Comments: 0
- Tags: case , chronograph , ollech , partsrepair , runs , selectron , vintage , wajs , withdivers
While the movement runs strong and appears to keep accurate time over an approximate 38 hour power reserve period and all chronograph functions work perfectly as they should, the crown does not pull out. While it can be wound without issue, albeit a bit tightly, it is stuck and won’t pull out. As a result…
Vintage Bercona Sport Diver Watch withOrange Dial, Red Date, Runs FOR PARTS/REPAIR
FOR REPAIR – until recently the manual wind movement had run strong and kept accurate time without issue. However, after most recently winding the brassed crown to fully wound status the mainspring would not unwind thus the movement wouldn’t run. This likely indicates that the mainspring needs to be replaced. After a day of remaining…